Home > News > Content

How To Use The Iron

May 26, 2017

Electric Iron How to use the iron Before you power on, you should check whether the protective layer of the outer layer of the wire is complete, and whether it is damaged to prevent the occurrence of leakage

  If it is old-fashioned iron, there is no water, so when ironing clothes, you need to touch the fabric on the spotted water, or covered with a damp cloth to prevent the fabric burned.

  Electric IronSteam iron need water, and is best there is no impurities in the boiling water or pure water, if it is a general tap water, inside the impurities may plug the pores, affecting the effect. In the process of adding water to grasp the amount of water, not too little, easy to evaporate in a short time finished. When pouring water into the water, be careful not to spill water on other parts of the iron to avoid electric shock.

  According to the material you want to iron material, select the corresponding temperature stalls, and then start heating. Do not care about this step, otherwise the clothes may be wrinkled, hot.

  In the iron heating process and ironing intermittent, the iron should be erected, can not readily put aside, so easy to direct contact with the iron items burned.

  Electric Iron After the steam iron is used up, if there is still water, either drained or continue to energize until the water is dry. If you do not let the water evaporate, then the water is likely to leak, attached to the floor, leaving water stains, the maintenance of the machine disadvantage.

  1, iron power cord must use three-core braided cord. Among them, green, yellow color line (some black line) is the ground wire, red line connected to the line of fire, white line then zero line. The supplied socket must also be three holes and be grounded reliably. Do not use plastic power cord instead, because the plastic temperature performance is poor, a little careless power cord touch in the hot shell or floor; will melt the plastic insulation and electric shock accident.

  2, since the power cord, the length of 2m is appropriate. If too long, and arranged well, so that the power line dragged to the ground, walking people may tripping iron, fell to the ground or hot coke in the clothing, and even hurt.

  3, in the intermittent ironing clothing, iron should be erected, or placed on a dedicated iron shelf. Do not drop the iron on the flammable items, so as not to fire; do not put iron on iron or masonry, so as not to scratch the floor plating.

  4, to promptly remove the iron surface of the dirt. The fluff on the surface of the chemical fiber fabric is easily melted and glued to the bottom plate to form a dark spot, not only ugly, but also inconvenient to use. In order to avoid the generation of such dirt, in the ironing of chemical fiber fabric, pad a clean damp cloth. If the bottom plate appears dark spots, must not be used knife knife, that will destroy the floor of the coating. The most convenient and effective way is: first with a piece of wet cloth stained with a little toothpaste, slowly wipe rust spots, to be wiped, and then coated with a layer of wax, connected to the power, the wax and then rub. If the rust spot on the bottom of the iron, you can use a piece of waste cloth for the pad, forced back and forth more than a few times. This method of dirt, not only will not damage the iron plating layer, but also to restore its original smooth and flatness.

  5, after the end of the use of electric iron (or when the power outage), should be unplug the power plug, let the natural cooling, you must wait for no touch after touch, and then into the box door.

  6, ordinary iron can not control the temperature, it is difficult to meet all kinds of clothing ironing requirements. Especially in the ironing of chemical fiber fabric, a little care will be the clothing burned, and sometimes only by the user's experience to master the temperature. Ordinary type of electric iron continuous power can not be too long, otherwise, because the temperature gradually increased (up to 600 a 700 ℃), will burn the heating element, will also damage and burn the coating. Generally take through, off the power of the way to roughly control the temperature of the floor, this is both power and security.

  7, ordinary type of iron if the floor temperature is too high, let the natural cooling, can not use the method of water to cool, but can not immerse the floor in cold water, otherwise, will make the iron destroyed.

  8, thermostat type iron inside the adjustable temperature of the bimetallic thermostat. Use the knob to adjust the operating temperature. When the temperature rises to the desired temperature, the bimetallic is bent downward by heat, leaving the power contacts off, turning off the power, and the irons no longer warming up. To be a certain degree of temperature, bimetal to restore the original state, then the power and connected. So repeated on and off, so that the iron to maintain a constant temperature. In order to maintain the rigidity of the bimetallic sheet, so that the temperature control is normal, should make bimetal in a natural state, when not in use, should the thermostat button to "off" or "off" position, never in the high temperature position Long place.

  9, in the use of temperature control iron process, turn the thermostat knob when the force to light, slowly spinning to the desired ironing of the name of the fabric. Due to the large number of fabrics, the fabric label shows the name of the fabric is limited, ironing several different fabrics, the adjustment temperature from the lower temperature position to start ironing, when the temperature is not enough, can be appropriately improved. This can be continuous ironing and energy saving.

  10, ironing clothes thicker or wrinkles on clothes more, the most suitable for use of steam spray type iron. When used, you can start the handle of the handle above the toggle spray button, so that it points to the "spray" file (SPRAY), iron front immediately spray water mist. Some steam spray-type iron button control, use, use your fingers have been pressed button, water mist came out, if the fingers leave the button, water mist immediately stop. Another toggle control button is to the right when the jet, the fingers leave, the water mist can continue to spray. If you feel the humidity of the clothes has reached the requirements, you can spray the button in the opposite direction to close, you can immediately stop spraying water mist. To dry ironing, simply press the steam button and lock it backwards.

  11, when the thermostat knob to "spray", the bottom of the temperature of the gasification chamber of the water quickly boiling gasification, and produce enough pressure to continuously spray water mist; if the wrong adjustment thermostat to low temperature zone, then The gasification rate of water is slower and the vapor pressure is small. Then start the spray button, then the spray is not a mist but a smaller water column, stained clothes will form a water stains, affecting the appearance.

  12, water quality of the steam spray type of iron has a great impact on life. Its water must be pure water of distilled water or boiled water, shall not use the general tap water. Otherwise, the water vaporization, the formation of the scale will be precipitated inside the iron and plug the jet hole, so that the jet volume becomes smaller, or even completely blocked. When used, if the jet hole is blocked, should be promptly with a pin and other similar fine wire to clear.

  13, Electric Iron steam spray type iron after use, should press the steam button, pour the water tank (water tanker) in the water, while the spray button to "spray" file, continue to power 10min, so that the internal water completely evaporated Off, cut off the power, until the natural cooling, the steam button and spray button reset, before storage